Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
This post listed below pertaining to Installing A Bathtub is indeed engaging. You should investigate for yourself.
Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably hard job. If the old bathtub is readily easily accessible, the task can move immediately; if you have to open a wall to remove the old tub as well as place the new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old tub as well as embeded in the brand-new one. Make sure you have qualified on your own for the task and also fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is much better to think about employing one before you start. Opportunities are you might need a professional plumber to make tube links.
This article will certainly assist you set up a new bath tub in your shower room if you have currently bought a brand-new tub and also don't require to alter the arrangement of your previous water pipes.
Your tools and also material list should consist of the following:
Getting ready for the Installment
Firstly, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is separate the water system. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted access that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bath tub
Using both wooden boards under its feet, place the bathtub in the needed placement. The wooden boards are practical in evenly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little points.
The following goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level and changing the feet on the tub until the level checks out level.
To set up taps, fit all-time low of the furthest adaptable faucet port to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the supply of water and also inspect all joints and also new pipework for leakages and tighten them if necessary. Load the bathtub and likewise examine the overflow electrical outlet and also the typical outlet for leakages.
Finally, take care of the bath paneling as explained in the producer's instruction manual. Tiling and also securing around the bath tub should wait till the bath tub has been made use of a minimum of when as this will certainly resolve it right into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in area between the faucet as well as the sink. Protect the faucet in place with the manufacturer given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type ought to be connected to the tap ends first, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break a rigid seal, causing the water to permeate the wall between the bathroom as well as the tiling, causing difficulties with wetness as well as possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes and also cartridges, and are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly load the bathtub with water prior to sealing, to enable the movement experienced when the tub is in use. The sealant can break relatively very early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly offered on the market. It is a good idea to fit the floor tiles making use of water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Do you really like reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Leave a comment below. We would be glad to see your feelings about this page. We are looking forward that you visit us again in the near future. Enjoyed our write-up? Please share it. Help another person locate it. We thank you for reading our article about Tools You Need to Install a New Bathtub .
Appointment Report this page